Toolset32

If your BMW NFRM is locked after short circuit, you need to reset short circuit counter in order for the headlight to work. This can be done with BMW Ediabas coding software. Tools needed:BMW ISTA-D ISTA-P Rheingold Tool32BMW ICOM emulator. Or you can download free Ediabas/INPA/WinKFP/NCS Expert Tool32 software on search engines and load it on cheapWIFI BMW ICOM A2+B+C.
  • Instructions:ⅠThis one uses the FRM module (e.g 2011 335xi with nav) and ToolSet32…. 1) Make sure it’s on map 02) Load INPA software and make sure the cable is working3) Close INPA (very important to do this)4) launch TOOL32.EXE5) click on “jobs” and start typing out: steuern_reset_kurzshlussabschaltung6) click on the text box located under arguements and enter the various hex values (you will need to try both check marked and unchecked for the box that says DATA).
  • Procedure: (translated from German)When LM1 provides the reading of short circuit status as follows (job name and PRG file in bold:apiJob (“LM_AHL”, “status_lampen_kurzschluss”, “”, “”).
  • Rate: 0OBJECT = lm_ahlSAETZE = 1JOBNAME = status_lampen_kurzschlussVARIATION = LM_AHLJOB STATUS =UBATTCURRENT = -1UBATTHISTORY = -1IGNITIONCURRENT = -1IGNITIONHISTORY = -1Set: 1JOB_STATUS = OKAYSTAT_FL_LINKS_SHORT_CIRCUIT = 0 00 00 .STAT_FL_RECHTS_SHORT_CIRCUIT = 0 00 00 .STAT_AL_LINKS_SHORT_CIRCUIT = 0 00 00 .STAT_AL_RECHTS_SHORT_CIRCUIT = 1 00 00 .STAT_BEGRL_LINKS_SHORT_CIRCUIT = 0 00 00 .STAT_BEGRL_RECHTS_SHORT_CIRCUIT = 0 00 00 .STAT_NSW_LINKS_SHORT_CIRCUIT = 0 00 00 .etc ….
  • “0” means Channel OK, “1” means short circuit. Channel numbers are easily counted from top to bottom, starting with “Channel 0” (!).In Ex.
Above, it is therefore of the channel 3. Select the command to reset the lock now, which resets the counter.apiJob (“LM_60”, “reset_kurzschluss_sperre”, “”, “”).
Rate: 0OBJECT = lm_60SAETZE = 1JOBNAME = reset_kurzschluss_sperreVARIATION = LM_60JOB STATUS =UBATTCURRENT = -1UBATTHISTORY = -1IGNITIONCURRENT = -1IGNITIONHISTORY = -1Set: 1JOB_STATUS = ERROR_LAMP_NR.
With no entry in the “argument” field is the “ERROR_LAMP_NR”, ie channel number.
Enter data and execute, the job status is “okay”.
Re-reading the counter should then show on the channel “0”.Each channel must be individually reset all channels at once is not possible.
When LM2 the command for resetting is “_reset_kurzschluss_sperre”.
This article is a step-to-step guide on install and set up BMW Standard Tools 2.12 on laptop. BMW Standard Tools is a group of software distributed by BMW Group that contains several interoperating applications and drivers, including NCS Expert, WinKFP, NFS, Tool32 etc.
Following are the free download and detailed installation instruction offered.
If previous versions/attempts were installed, go to add/remove programs and remove those versions.
Ensure you have at least 15 GB free space on the C Drive, or virtual drive if using a Virtual Machine.
Determine whether your OS has 32 or 64 bit encryption before beginning the install.
Download your chassis DATEN by using the link contained within the “DATEN Link” text file.
Install the program 7Zip to extract your DATEN download (http://www.7-zip.org/).
Software: BMW Standard Tools 2.12 (INPA, EDIABAS Toolset32, NCS-expert etc).
Hardware:BMW INPA K+DCANcable, ENET (Ethernet to OBD) cable, BMW ICOM a2+b+c emulator.
Where can you get the BMW Standard Tool? What you need to get. Free download BMW Standard Tools V2.12 Software . Or get it in BMW ICOM Rheingold ISTA-D ISTA-P software HDD. Operating system: Win XP/Win 7. 1.Right click on BMW Standard tools-212.exe and run as administrator. If installing on Windows 8 or 10, right click and select properties then compatibility tab. For Windows 7, Please select “Run this program in compatibility mode. 2.Click “Yes” when asked to allow the program to make changes to your computer.
3.Select “English”. 4.Select “Next”. 5.Select “I accept the agreement”→“Next”→“Next” when you’re done reading the release notes.
6.Accept the default install options (we’ll worry about the KDCAN drivers in a later step).
Select the default location for each of the programs being installed on next few screens.
7.Select the default Start Menu Folder by clicking “Next”.
8.Uncheck both “Execute backup and restore wizard and click next.
9.Select “Ok” when the message pops up. 10.Select the default interface by clicking “Next”.
11.Select default Com Port (Com 1) by clicking next. We can change this later if need be.
12.Click “Install”. 13.Select “No, I will restart the computer later” and click “Finish”.
No need to do this, can use software without rebooting.
14.Select the 3 folders below and delete them. This install was primarily used to create all the environment variables and registry entries necessary to run these programs.
Now, we’ll copy a pre-configured set up with English files and translations already in place, plus select which NCS Expert version you need to use (32 or 64 bit).
NOTE: You won’t have the NCSEXPER64 folder yet. 15.Select the downloaded folders below and copy them to your C: Drive.
For 32 bit systems, select “NCSEXPERT”;. For 64 bit systems, select “NCSEXPER_64”.
16.Run the BMW Coding Tool by right clicking and “Run as Administrator”, the select “Yes” when asked to allow this program to make changes to your computer.
17.We will define a few settings on this screen so that we can import the DATENs.
Button 1, Browse to the location where you downloaded your SP-DATEN and click the chassis folder (i.e., E89).
The DATEN folder must not be a zipped file and must contain the following folders (cfgdat, data, daten, ecu, format, kmmData, sgdat, work).
If not, this import process will not work. Button 1, Browse to the location where you downloaded your SP-DATEN and click the chassis folder (i.e., E89).

Classic way (E-Models)

The DATEN folder must not be a zipped file and must contain the following folders (cfgdat, data, daten, ecu, format, kmmData, sgdat, work).
If not, this import process will not work. Button 2, Select the NCS Expert folder that you copied to your C: drive in step 15.
Button 3, Select the Ediabas folder that you copied to your C: drive in step 15.
Button 4, Select the EC-APPS\NFS folder that you copied to your C: drive in step 15.
Button 5, Click this button to begin the process of importing your DATEN.
At this point, you’re able to begin coding and utilizing INPA for troubleshooting.
You will only need to use button 6 if you’re planning on flashing updated software to any of your modules.
Button 6, Click this button to import the files required to update the software on your modules.
Depending on your chassis, this will appear to freeze at times while copying CI*** files/folders.
This is due to the copying of large files that’s utilized to flash your CIC.
At this point, you’re software is completely set up for coding and/or flashing.
We will move to the next step of configuring your KDCAN cable drivers.
nNOTE: If the program displays an error when attempting to select the default folders, ensure you have these folders on your C:\ drive (if not, create it as an empty folder):.

PS: How to start WinKFP?

How to set up BMW Standard Tools 2.12?

How to install BMW Standard Tool?


C:\EC-APPS\INPA = BIN, CFGDAT, DEMO, DOKU, english, english.met, HELP, PRT, SGDAT, source.
Comments are closed.